MANUAL CADDX NX4 PDF

The NXZA-TK (from now on called NX-4) NetworX from Caddx represents a new approach to the design of security systems. The NX-4 is probably the most. The NetworX NX-4 from CADDX Controls represents a new approach to security systems design. Drawing on our experience in the world market as the largest. Click the photo of your keypad or choose from the list below. CADDX Manuals. CADDX NX E User Manual (PDF, MB) · CADDX NX E User Manual.

Author: Torisar Arashigore
Country: Jamaica
Language: English (Spanish)
Genre: Politics
Published (Last): 20 September 2013
Pages: 355
PDF File Size: 12.52 Mb
ePub File Size: 7.80 Mb
ISBN: 968-1-84330-768-2
Downloads: 12623
Price: Free* [*Free Regsitration Required]
Uploader: Dailrajas

Enter 25 to go to the section for zone types. CA60 Plus Software Version 3. To view the data in a location, a binary process is used.

I pulled the plug and the battery contacts to stop it. The system may be programmed to communicate with a central monitoring station to report system events. Before ringing ADT i decided just to do a little more searching on the net for info on the nx-4, and came across some system called a “DAS NX-4” hosting from an australian site, so i looked up the installer manual for the das nx-4 and it seemed almost identical to the caddx installer manual, however the locations called features in this manual were different numbers!

Consult the instructions for your central station receiver to determine mznual format is compatible. Posted on Mar 05, Willis Jackson 1 years ago Views: The flashing will continue until the new data is stored by pressing the [r] key.

Ge NetworX NX-4 Manuals

Could it be possible that the board is in a different position in the box? The alarm report will also be sent. Press each key, one at a time, to release the stuck keys, or press cancel.

The Clean light is an indication that the dishwasher has been run and that the dishes inside it are clean. If dual or split reporting is desired, location should be used to select only those cadxx that should be reported to Phone.

  CEFAR ACTIV XT PDF

If an alarm is detected on a jx4 tripped zone, the count increments to. If dual or split reporting is not desired, location should be left at the factory default of “0”. Factory default is “” and the NX- will answer on rings. Enter [year 0’s digit].

Need help adding a entry/exit delay to zone

On the LCD keypad, the number in the location will be displayed. If another user code needs to be programmed, return to step.

This manual contains proprietary information. In addition, certain communicator reports are enabled in location. This report will show Expander Trouble – device zero 0. Yes, I do have the manual. If these zones become secured any time during the arming cycle, they will be unbypassed and active in the system. Once a module is enrolled, if it is not detected cadd the control, the “Service” LED will illuminate.

The []-[0] is the number of minutes, and the [r] stores the data and moves to the next segment of this location. On the first call, let the phone ring one or two times. The Clean light is flashing You should call for service if the Clean light is flashing and the machine is inoperable. If closing reports are sent, the user code will be 9. When you run out of segments, it goes back to the section selection level.

You are now in the Program Mode and ready to select the module to program. Auxiliary Code cddx 2 3 4 5 6 “Quick Arm” Digit: Lately during the filling cycle water hammer is occurring.

You will see that numerous features can be selected from within one segment. The NetworX design allows a fully loaded system to be housed in one single metal enclosure, establishing for the first time, a logical solution and design response to modular systems. During this delay time, the “Cancel” LED will flash. Not finding what you are looking for? If a new first alarm is detected in a different zone, the counter remains at.

  LM11CN DATASHEET PDF

Off ns4 on board siren driver enabled. At the end of the exit delay, these zones will become bypassed.

Owners Manuals

If the location entered is a valid location, the “Armed” LED will extinguish, the “Ready” LED will illuminate and the binary data for the first segment of this location will be shown by the zone LED’s. The system may be programmed to caaddx More information. The NX- can also be programmed to perform a missing battery test every seconds.

The “Ready” LED will illuminate steady. When you are in the last segment of a location and press the [r] to enter the data, you will exit that location. See location 0, page Enable Keypress Silence option – silences the pulsing keypad sounder for seconds when a key is pressed Enable Armed Status Suppression – will not allow the keypad to display faulted or bypassed zones when the system is armed Enable Panic, Fire, Medical Beeptone – will sound a short beep to verify that the keypress was accepted Suppresses the “Service” LED – will not allow the “Service” LED to illuminate for any reason.

This arming mode will encourage system owners to use their system more frequently when the premise is occupied.

Owners Manuals – Relyco Security

While using the scroll keys you can change any digit by entering a new digit. Have it hooked up to a scanner an checked for DTC’S – diagnostic trouble codes. The factory default for the “Go To Program” code is [9]-[]-[]-[] for a -digit code or [9]-[]-[]-[]-[0]-[0] for a -digit code. This feature shall not be programmed into the control unit.